Pry out the light assembly with a flat screwdriver at the side opposite the switch. Pull the bulb straight out of the socket. Máme ford focus C-Max r. Dali jsme ji repasovat vyměnit lanovody ale při namontování motorky točí jen do jedné strany a pak vypadnou. If the procedure needs to be repeated, you must wait 30 seconds. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant.
On hatchbacks, the removable luggage area cover must be removed prior to attaching the tether strap to the tether anchor. Apply the brake and shift into the neutral position. The horn can be operated when the ignition is off. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent,. Position the child safety seat in a seat with a combination lap and shoulder belt.
The side airbag could injure you as it deploys from the side of the seatback. Lift the control to adjust the angle of the seatback. Replacing high-mount brake lamp bulbs Sedan 1. Although the indicator light is illuminated, the heat is regulated by a thermostat which causes the heat to activate within a certain range. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. However, if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. The following table tells you which transmission or transaxle each code represents.
Make sure the parking brake is fully set. Use only fluid that meets Ford specifications. Your new, unprogrammed key is now programmed. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. Tachometer if equipped : Indicates the engine speed in revolutions per minute. Power steering fluid reservoir 2. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. This maximizes the effectiveness of the safety belts and helps properly position the occupant relative to the airbag to improve protection. The manual describes the location of each fuse and relay. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. The Dispute Settlement Board may not be available in all states. Check the fuel system for leaks. The diagnostic module monitors its own internal circuits and the supplemental airbag electrical system wiring including the impact sensors , the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors.
Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life. The cover can be removed completely by pressing inward on both ends of the support. Power distribution box The power distribution box is located in the engine compartment. . Ford Motor Company will repair or. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
To obtain reimbursement information, U. These products are available from your authorized dealer. To adjust the shoulder belt height, push the button and slide the height adjuster up or down. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. On page 127 under Roadside Emergencies it describes the fuse panel under the dash by the brake pedal.
Reach under the front fender, grasp the bulb socket and turn it counterclockwise to remove it. For more information on brake fluid maintenance, refer to Brake fluid in this chapter. Set the fan speed to the highest setting. See, for a long time I was pushing online. Depending on which tire is to be changed, locate the jack at the half-moon cutout located approximately six inches 15 cm from the front wheel opening 1 or approximately 15 inches 38 cm from the rear wheel opening 2.
Remove the head restraint s if equipped of the rear seat, and fold the seatback forward. Use only Ford recommended replacement fasteners. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. Pull the bulb straight out. Mohli by jste mi poradit co ještě vyměnit? On 3—door models, unsnap and remove the access door if equipped to access the proper jacking points. .