The sensor that you replaced was on the rear driver side of the engine facing the firewall, correct? Issue was determined to be crankshaft position sensor, which was replaced. Is the sensor within resistance specs? I'm an engineer and fully understand the mechanics of a vehicle. Replaced the Crankshaft and camshaft sensors as a kit from Nissan. Popular retail outlets currently call these a claw bar if it has a claw on each end, or a moulding bar if it has a claw on one end and a flat pry bar on the other. P0335 Symptoms: Nissan Frontier Depending on the model year and engine of any vehicle the job of the crankshaft sensor is going to change. Roll to a stop at a stoplight and the engine dies. Was told that there was no recall for this situation.
So I ended up getting a new O- ring for the sensor. I'm lucky my daughter handled the entire ordeal calm and collectedly or there could have been serious consequences. The ones in the kit from Nissan looked identical to the old ones. No, you shouldn't have to erase the code because it should automatically be cleared after the defected sensor has been replaced with a new sensor. The vehicle was taken to a dealer.
The next day it was diagnosed with a bad crankshaft position sensor and repaired. Or I might have to buy a thinner O ring? Don't give up on Nissan. This is definitely not the place to start, but is worth looking at if nothing else seems to be wrong. I also have a a handy tool I use for removing nails. She was on the millard e.
This causes the Check Engine Light to be displayed on the dashboard and a failsafe mode enabled. This step will rule out any wiring problems from start. So I went to my local Advanced Auto and purchased a new one. Thanks again for the guidance and support. I walked away frustrated and told him this is my last Nissan.
R3022 and 03v-455 describe these problems. Questions - 1 Is this something I should be able to do myself relatively easily? Leave a comment below or tell us if the information above help you fix the code. Since both already show a malfunction code, it would be advisable to change. Definitely won't be taking it out of town until something is done. This has happened on 4 to 5 different occasions. There are a total of three pins and three combinations of pins to measure for resistance ranges. What about the connector that connects to the sensor, have you double checked that connector to make sure it fully is connected right? This rules out any wiring problems from the start.
What if the vehicle stopped on an interstate highway while driving at 65 mph? The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor. P0335 Symptoms: Nissan Altima Depending on the model year and engine of any vehicle the job of the crankshaft sensor is going to change. Car acts as if it's hard to start ever since this happened. Conclusion Good luck determining what is causing P0335 in your Frontier. If you have any doubt as to repairs on your vehicle, please contact your technician. Code he received did not give him any information so he turned the light off and I continued driving the car. For example when you measure 1-3, put the + probe on 3.
I slicked the O ring with oil and used the bolt to help it go in but it just goes crooked. Though the symptoms you stated about the problem seem to indicate that replacing the sensor will indeed fix the problem. So the sensor was able to go in with the new O-ring, thought it should go in a little tighter than it did, but thought it had good enough tension going in for it to not be a problem. It would also perform with poor power during operation. How does a mechanic diagnose the P0335 code? I have a bunch of inexpensive screwdrivers of various sizes and lengths I keep on hand for this purpose, to bend as needed so they are configured to do the job.
I find it very disturbing that Nissan would knowingly risk passenger safety by not recalling and covering the cost of repair for a well maintained car that is having the same issue as others in the same make and model year. Information redacted pursuant to the freedom of information act foia , 5 u. In cases where drivability problems are present, the vehicle should not be driven until it is repaired. You do not have access to the diagnostic trouble code diagnostic's. It flagged P0335 when the engine started a little rough, then under accelleration it flagged P0725, Engine Speed Sensor circuit. Once again had to pull over on the side of the rode the best I could turn the car off and thankfully it turned back on. I had the code checked and it was the crank shaft sensor.